STG801008-S3E2B2 electric heating compound eyewash

STG801008-S3E2B2 electric heating composite eyewash
1. Product introduction
This eyewash adopts electric heater centralized heating method, which can effectively increase the temperature of the eyewash water by 15. The equipment is made of SS304 material and can resist acid, alkali, salt and oil. Corrosion of chemical substances, the spray part and the eyewash part are installed directly on the ground of the factory site and connected to drinking tap water; when the chemical substance is sprayed on the eyes, face or other parts of the body, open the compound The spray switch of the type eyewash is used to rinse the body or clothing with a large amount of water, or open the eyewash part to rinse the injured eyes and face with a large amount of water. The washing time> 15 minutes; the spray water flow:> 75.7L/MIN , Eye/face wash water flow rate:> 11.4L/MIN, eye wash water flow rate:> 1.5L/MIN.
For the electric heating compound eyewash, it is classified into indoor electric heating compound eyewash and outdoor electric heating compound eyewash.
Special attention: the electric heat tracing eyewash has only heat tracing and heat preservation, and cannot increase the temperature of the eyewash water; the electric heating eyewash can effectively increase the temperature of the eyewash water by 15, but it does not have the ability to increase the temperature of the spray water; If it is necessary to increase the temperature of the outlet water from the eyewash and the temperature of the spray water, the emergency eyewash station products should be selected.
Eyewash standard:
American eyewash standard ANSI/ISEA Z358.1 2014 Emergency Eyewash and Shower Standard
European eyewash standard EN 15154:1/2 2006 and 15154:3/4 2009 Emergency Eyewash and Shower Standard
Australian eyewash standard AS4775-2007 Emergency Eyewash and Shower Standard
optional configuration: The eyewash device can be equipped with sound and light alarm, explosion-proof lighting, DCS connection, timing drainage device, waste water collection enclosure and water curtain, etc.
2.
There is fixed drinking tap water at the application site, if not For a fixed water source, you should choose a portable eyewash
water source pressure requirement: 0.2~0.6 MPa, if the water supply pressure is lower than the above pressure, the customer needs to inform STGSTG, when STGSTG produces the eyewash, it will modify the internal structure of the eyewash to meet the eyewash standard The technical requirements of
the eyewash device is made of stainless steel 304 material, which can resist the corrosion of acid, alkali, salt and oil chemical substances, but it cannot resist CL-, F-, sulfuric acid and chemical substances with a concentration of more than 50% oxalic acid. Corrosion
can be applied to areas where the ambient temperature is higher than -40.
Power supply: 380VAC/3PH/50HZ.
Electric heater power: 10KW or 20KW. It is necessary to consider the electrical load on site.
Use water temperature: 16~38.
Install directly on the ground, floor steel plate or floor grille at the work site.
Need to choose indoor electric heating compound eyewash and outdoor electric heating compound eyewash according to site conditions.
Products are widely used in petroleum, chemical, electronics, electric power, ports and pharmaceutical industries.
3. Performance characteristics:
Adopting centralized heating method, which can effectively increase the temperature of the eyewash water by 15.
Equipped with a temperature control switch to control the heating temperature of the
electric heater. The antifreeze power of the low-power heater: 100W The
power of the high-power heater to heat the water source: 10KW Or 20KW
Voltage: 380 VAC/3PH/50HZ
Current: 15 A
Eyewash system is set with automatic emptying device
. The explosion-proof level of the junction box: Exd IIB T4 or Exd IIC T6
. The protection level of the junction box: IP65
stainless steel SS304 material, can be acid-resistant, Corrosion of alkali, salt and oil chemical substances.
Equipped with a spray system and an eyewash system, which can not only wash the face and eyes, but also wash the body. The chemical substances on the clothing are directly installed on the ground of the work site. It
can be connected to drinking tap water and can be used when the ambient temperature is higher than -40 In areas with , the
eyewash system is equipped with an automatic emptying device to completely empty the water in the eyewash elbow within 12 seconds. The
pipe fittings are made of SS304, which is resistant to corrosion by acids, alkalis, salts and oil chemicals. Thickness: 3.0mm, pipe fitting thread: NPT
Inlet size: 1-1/4 inch FNPT, the size can be adjusted according to the customer’s site.
Outlet size: 1-1/4 inch FNPT, this size can be adjusted according to customer site.
Spray water flow rate:> 75.7 L / MIN
wash water flow rate:> 1.5 L / MIN
eyewash / water wash flow rate:> 11.4 L / MIN
washing time:> 15 MIN
water pressure requirements: 0.2 ~ 0.6 MPa
push-handle attached to the luminescent The nameplate is
equipped with an eyewash device and it is luminous and safe.
4. Installation requirements: The
general principle is to
install near the hazardous work area, generally 10 or 15 meters away.
The time to reach the eyewash in a straight line should not exceed 10 seconds . The
eyewash
must be connected to drinking tap water.
Use water pressure of 0.2~0.6MPa
within the radius of 2 meters of the eyewash, and no non-explosion-proof electrical switch can
be installed.
According to the installation hole size of the eyewash base, drill 8–10mm where the eyewash is needed. hole
according eyewash drawings, step by step assembly eyewash
the assembled eyewash mounted to a predetermined position, the expansion screw eyewash
connected intake: 1-1 / 4 inches FNPT
connection outlet: 1-1 / 4 Inch FNPT is
connected to the power supply.
5. Operating instructions:
Open the eyewash valve by gently pushing the eyewash handle by hand, and automatically turn on the electric heater, and the eyewash water will be automatically sprayed from the eyewash system; after use, the eyewash handle must be reset to close the eyewash ball valve and automatically empty the eyewash Part of the accumulated water will automatically turn off the electric heater and reset the dust cover.
Gently pull the spray lever by hand to open the spray ball valve, and the spray water will automatically spray from the spray head; after use, the spray lever must be reset to close the spray ball valve.