STG802005 automatic emptying antifreeze type imported vertical eyewash

STG802005 automatic emptying and antifreeze type imported vertical eyewash
1. Product introduction
The eyewash has the function of automatically emptying the water inside the eyewash to achieve the purpose of antifreeze. The equipment is coated with ABS on the outer layer of SS304, which can resist all kinds of chemicals. It is necessary to install the eyewash part directly on the ground of the factory site and connect it to drinking tap water. When chemicals are sprayed on the eyes or face of the staff, open the eyewash part of the vertical eyewash to protect the injured Rinse the eyes and face with a large amount of water for more than 15 minutes.
Eyewash standard:
American eyewash standard ANSI/ISEA Z358.1 2014 Emergency Eyewash and Shower Standard
European eyewash standard EN 15154:1/2 2006 and 15154:3/4 2009 Emergency Eyewash and Shower Standard
Australian eyewash standard AS4775-2007 Emergency Eyewash and Shower Standard
optional configuration: The eyewash device can be equipped with sound and light alarm, explosion-proof lighting, DCS connection, timing drainage device, waste water collection enclosure and water curtain, etc.
2.
There is fixed drinking tap water at the application site, if not For a fixed water source, you should choose a portable eyewash
water source pressure requirement: 0.2~0.6 MPa. If the water supply pressure is lower than the above pressure, the customer needs to inform STGSTG. When STGSTG produces the eyewash, it will modify the internal structure of the eyewash to meet the eyewash standard The technology requires
that the eyewash device is dipped with ABS on the outside of stainless steel 304 material, which can resist the corrosion of various chemicals.
The eyewash has the function of anti-freezing and is suitable for use in areas where the ambient temperature is higher than -5C.
Use water temperature: 16~38. (The temperature value of the water source is solved by the on-site water supply) It is
directly installed on the ground, floor steel plate or floor grille plate of the work site.
Products are widely used in petroleum, chemical, electronics, electric power, ports and pharmaceutical industries.
3. Performance characteristics:
Stainless steel SS304 is coated with bright yellow ABS, which can resist corrosion of various chemicals.
Coating: Bright yellow coating properties outside ABS.
Coating thickness: 250~300 microns.
Melting temperature: 184~186.
Burning attributes: self-extinguishing type.
Resistance to boiling water: more than 2000 hours.
Salt water spray resistance: 2000 hours without corrosion.
Seawater resistance: more than 10 years.
Equipped with an eyewash system, only the face and eyes can be washed. It is connected to drinking tap water. It is
suitable for areas where the ambient temperature is higher than -5. The
pipe fitting material is dipped in ABS. The pipe fitting thickness: 3.0mm. The pipe fitting thread: NPT
Inlet size: 1/2 inch FNPT, the size can be adjusted according to customer site.
Outlet size: 1-1/4 inch FNPT, this size can be adjusted according to customer site.
Eyewash water flow rate:> 1.5 L/MIN
Eye wash/face wash water flow rate:> 11.4 L/MIN
Flushing time:> 15 MIN
Water source pressure requirement: 0.2~0.6 MPa
Hand push handle with luminous signboard
equipped with eye wash luminous safety listing
IV , Installation requirements:
general principles,
install near the hazardous work area, generally 10 or 15 meters away.
The time to reach the eyewash in a straight line should not exceed 10 seconds . The
eyewash
must be connected to drinking tap water.
Use water pressure of 0.2~0.6MPa
within the radius of 2 meters of the eyewash, and no non-explosion-proof electrical switch.
Specific installation
According to the installation hole size of the eyewash base, drill 3–10mm where the eyewash needs to be installed hole
according eyewash drawings, step by step assembly eyewash
the assembled eyewash attached to the predetermined position, eyewash expansion screw
connecting the water inlet: 1/2 inch FNPT
connection outlet: 1-1 / 4 inch FNPT
5. Operation instructions:
Open the eyewash valve by gently pushing the eyewash handle by hand, and the eyewash water will be automatically sprayed from the eyewash system; after use, the eyewash handle must be reset to close the eyewash valve and automatically drain the water in the eyewash part. Reset the dust cover.