STG802010 automatic emptying antifreeze type high performance corrosion resistant stainless steel vertical eyewash
1. Product introduction
The eyewash has the function of automatically emptying the water inside the eyewash to achieve the purpose of antifreeze. The equipment is produced by SS304, and the outer layer has been specially crafted Treatment, it can resist the corrosion of all kinds of chemicals. Equipped with the eyewash part, install it directly on the ground of the factory site and use it with drinking tap water; when the chemical substance is sprayed on the eyes or face of the staff, turn on the vertical eyewash The eyewash part of the instrument is used to rinse the injured eyes and face with a large amount of water, and the rinse time is more than 15 minutes.
Eyewash standard:
American eyewash standard ANSI/ISEA Z358.1 2014 Emergency Eyewash and Shower Standard
European eyewash standard EN 15154:1/2 2006 and 15154:3/4 2009 Emergency Eyewash and Shower Standard
Australian eyewash standard AS4775-2007 Emergency Eyewash and Shower Standard
optional configuration: The eyewash device can be equipped with sound and light alarm, explosion-proof lighting, DCS connection, timing drainage device, waste water collection enclosure and water curtain, etc.
2.
There is fixed drinking tap water at the application site, if not For a fixed water source, you should choose a portable eyewash
water source pressure requirement: 0.2~0.6 MPa. If the water supply pressure is lower than the above pressure, the customer needs to inform STGSTG. When STGSTG produces the eyewash, it will modify the internal structure of the eyewash to meet the eyewash standard The technical requirements
of the product are produced by SS304, and the outer layer is treated with a special process, which can resist corrosion of various chemicals.
The eyewash has the function of antifreeze, and is suitable for use in areas where the ambient temperature is higher than -5C.
Use water temperature: 16~38. (The water source temperature value is solved by the on-site water supply) It is
directly installed on the ground, floor steel plate or floor grille plate of the work site.
Products are widely used in petroleum, chemical, electronics, electric power, ports and pharmaceutical industries.
Third, the performance characteristics:
The eyewash using SS304 production, through a special process layer, can be various types of anti-corrosive chemical substances
with wash system, can only flush face and eyes and other parts connected to drinking water using
suitable temperature Areas above -5C use
pipe fitting material SS304, pipe fitting thickness: 3.0mm, pipe fitting thread: NPT
water inlet size: 1/2 inch FNPT, this size can be adjusted according to the customer site.
Outlet size: 1-1/4 inch FNPT, the size can be adjusted according to the customer’s site.
Eyewash water flow rate:> 1.5 L/MIN
Eye wash/face wash water flow rate:> 11.4 L/MIN
Flushing time:> 15 MIN
Water source pressure requirement: 0.2~0.6 MPa
Hand push handle with luminous signboard
equipped with eye wash luminous safety listing
IV , Installation requirements:
Generally , the installation should
be near the hazardous work area, generally 10 or 15 meters away.
The time to reach the eyewash in a straight line should not exceed 10 seconds . The
eyewash
must be connected to drinking tap water.
Use water pressure of 0.2~0.6MPa
within the radius of 2 meters of the eyewash, and no non-explosion-proof electrical switch can
be installed.
According to the installation hole size of the eyewash base, drill 3–10mm where the eyewash is needed. hole
according eyewash drawings, step by step assembly eyewash
the assembled eyewash attached to the predetermined position, eyewash expansion screw
connecting the water inlet: 1/2 inch FNPT
connection outlet: 1-1 / 4 inch FNPT
5. Operation instructions:
Open the eyewash valve by gently pushing the eyewash handle by hand, and the eyewash water will be automatically sprayed from the eyewash system; after use, the eyewash handle must be reset to close the eyewash valve and automatically drain the water in the eyewash part. Reset the dust cover.
STG802010 automatic emptying antifreeze type high performance corrosion resistant stainless steel vertical eyewash
Model: 802010
SKU:
PL007357
Category: Vertical Eyewash
Description
Additional information
Brand |
STG |
---|
Reviews (0)
Be the first to review “STG802010 automatic emptying antifreeze type high performance corrosion resistant stainless steel vertical eyewash” Cancel reply
You must be logged in to post a review.
Reviews
There are no reviews yet.