STG803005 automatic emptying antifreeze wall-mounted eyewash

STG803005 automatic emptying antifreeze wall-mounted eyewasher
1. Product introduction
The eyewasher has the function of automatically emptying the water inside the eyewasher to achieve the purpose of antifreeze. The equipment is coated with ABS on the outer layer of SS304, which can resist all kinds of chemicals. Corrosion of the material, only the eyewash part, directly installed on the wall of the factory site, connected to drinking tap water; when chemical substances are sprayed on the eyes or face of the staff, open the eyewash part of the wall-mounted eyewash to treat the injured eye , Rinse the face with a large amount of water, and the rinse time> 15 minutes.
Eyewash standard:
American eyewash standard ANSI/ISEA Z358.1 2014 Emergency Eyewash and Shower Standard
European eyewash standard EN 15154:1/2 2006 and 15154:3/4 2009 Emergency Eyewash and Shower Standard
Australian eyewash standard AS4775-2007 Emergency Eyewash and Shower Standard
optional configuration: The eyewash device can be equipped with sound and light alarm, explosion-proof lighting, connection with DCS, timing drainage device and wastewater collection enclosure, etc.
2.
There is fixed drinking tap water at the application site. If there is no fixed water source, The
water source pressure requirement of the portable eyewash should be 0.2~0.6 MPa. If the water supply pressure is lower than the above pressure, the customer needs to inform STGSTG. When STGSTG produces the eyewash, it will modify the internal structure of the eyewash to meet the technical requirements of the eyewash standard
The eyewash is coated with ABS on the outside of stainless steel 304, which can resist corrosion of various chemicals.
The eyewash has the function of anti-freezing and is suitable for use in areas where the ambient temperature is higher than -5C.
Use water source temperature: 16~38. (The water source temperature value is solved by the on-site water supply) It is
directly installed on the wall of the work site.
Products are widely used in petroleum, chemical, electronics, electric power, ports and pharmaceutical industries.
3. Performance characteristics:
stainless steel SS304 is coated with bright yellow ABS, which can resist corrosion of various chemicals.
Coating: Bright yellow coating properties outside ABS.
Coating thickness: 250~300 microns.
Melting temperature: 184~186.
Burning attributes: self-extinguishing type.
Resistance to boiling water: more than 2000 hours.
Salt water spray resistance: 2000 hours without corrosion.
Seawater resistance: more than 10 years.
There is only the eyewash part and no spray part. It can only wash the face and eyes. It can be used with drinking tap water.
The eyewash has antifreeze function. It is suitable for areas where the ambient temperature is higher than -5. The
pipe fittings are made of ABS and pipe fittings Thickness: 3.0mm, pipe fitting thread: NPT
Inlet size: 1/2 inch FNPT, this size can be adjusted according to the customer site.
Outlet size: 1-1/4 inch FNPT, this size can be adjusted according to customer site.
Eyewash water flow rate:> 1.5 L/MIN
Eye wash/face wash water flow rate:> 11.4 L/MIN
Flushing time:> 15 MIN
Water source pressure requirement: 0.2~0.6 MPa
Hand push handle with luminous signboard
equipped with eye wash luminous safety listing
IV Installation requirements:
Generally, it should be
installed near the hazardous work area, generally 10 or 15 meters away.
The time to reach the eyewash in a straight line should not exceed 10 seconds.
If the eyewash cannot be installed
across levels, it must be connected to drinking tap water.
Use water pressure of 0.2~0.6MPa
within the radius of 2 meters of the eyewash, and no non-explosion-proof electrical switch can
be installed.
According to the installation hole size of the eyewash base, drill 3–10mm where the eyewash is needed. hole
according eyewash drawings, step by step assembly eyewash
the assembled eyewash attached to the predetermined position, eyewash expansion screw
connecting the water inlet: 1/2 inch FNPT
connection outlet: 1-1 / 4 inch FNPT
5. Operation instructions:
Open the eyewash valve by gently pushing the eyewash handle by hand, and the eyewash water will be automatically sprayed from the eyewash system; after use, the eyewash handle must be reset to close the eyewash valve and automatically drain the water in the eyewash part. Reset the dust cover.